Seamless Gutters, Fascia and Soffit in Lancaster and York Counties
Fortress Siding & Roofing installs seamless aluminum gutters and replaces fascia and soffit on homes across Lancaster and York counties and eight more Pennsylvania counties. A 2026 This Old House guide puts professional gutter installation at one to three days. Every project starts with a free, detailed, no-pressure estimate.
What do gutters, fascia and soffit do for a house?
Together they carry roof water away from the house and close off the roof edge. Gutters collect the water and send it away from the foundation. Fascia is the board along the bottom edge of the roof that covers the rafter ends. Soffit is the underside of the overhang, and on most homes it is where the attic takes in air.
One failure often damages the next part. Water that spills over the back of a clogged gutter soaks the fascia until it rots. Rotted wood leaves soffit panels with nothing solid to hold them. A blocked soffit starves the attic of intake air. We do this work across Lancaster and York counties and eight more Pennsylvania counties, and our eave failure guide has the detail.

How does a gutter, fascia and soffit replacement work, step by step?
It runs in five steps, and the order matters because the eave has to be sound before a gutter hangs there.
- Free estimate. We measure each run, look over the fascia and soffit, and check the eave from inside the attic where we can reach it.
- Written scope. You see the gutter and downspout sizes, where each downspout lands, the fascia and soffit material, and which eaves get vented panels.
- Removal. Old gutters come down, which exposes the fascia.
- Eave work. Rotted fascia and sub-fascia boards are replaced, then new soffit is installed. Where vented panels cover an old solid soffit, openings are cut first so air can pass.
- Gutters. Seamless aluminum gutters are formed on site from coil, hung, and tied to downspouts that discharge away from the foundation.
Which gutter sizes and materials are used?
The gutters are seamless aluminum, and the size depends on how much roof each run drains. A seamless gutter is one continuous piece per run, so it has fewer joints than a sectional gutter and is less likely to leak. Aluminum also resists rust.
| Part | Smaller size | Larger size | What published guidance says |
|---|---|---|---|
| K-style gutter | 5-inch | 6-inch | 5-inch is the residential standard; 6-inch is used for larger roofs |
| Downspout | 2x3 inch, 6 square inches | 3x4 inch, 12 square inches | Downspouts under 7 square inches suit only small areas such as porches and canopies |
Soffit panels come vented or solid. Vented panels let intake air reach the attic; solid panels only close the eave.

What affects the cost of seamless gutters, fascia and soffit?
Six things move the price: run length, a second story, a complicated roofline, old gutter removal, the number of downspouts, and rot found once the old gutter is removed. Longer runs take more material, and rotted fascia has to be replaced before a new gutter can hang.
Eave work done inside a siding project is a line item, not a second trip. Every home gets a free, detailed, no-pressure estimate, and financing is available for qualified homeowners.
Want a straight answer on your home?
We will look at the house, tell you what it needs, and give you a detailed estimate. It is free and there is no pressure.
How long does the work take?
Professional gutter installation takes one to three days, according to a 2026 This Old House guide. Its soffit guide gives one to two days for 300 linear feet of soffit on a one-story home. Both are national figures, not a schedule promise, and hidden rot, a second story or weather can add time.
What warranty comes with gutter, fascia and soffit work?
Gutter, fascia and soffit work comes with the 10-year workmanship guarantee from Fortress, the same guarantee described on our warranty page.
Which homes does this service suit?
It suits a home with a gutter pulling away from the roof edge, a dark streak down the fascia, a sagging soffit panel, or water standing in the gutter hours after rain. It also suits anyone planning a siding project, because gutters come down for a re-side and the fascia is exposed. We do roof replacement too.
If your only symptom is ice along the eave each winter, start in the attic. University of Minnesota Extension puts sealing ceiling air leaks first and insulation second, and we do not do that work. To get your eaves measured and priced, request a free estimate or call 717-864-6896.
Common Questions
What is the difference between fascia and soffit?
Fascia is the board along the bottom edge of the roof, and soffit is the underside of the overhang behind it. Fascia covers the rafter ends and gives the roof edge a finished face. Soffit closes the gap between the wall and the roof edge, keeps animals out and, on most homes, lets intake air into the attic. A failure in one often damages the other.
What affects the cost of seamless aluminum gutters?
Run length, the height of the house and the shape of the roofline all affect the cost. The number of downspouts, removing the old gutters and the condition of the fascia behind them change it too, because rotted wood has to be replaced before a new gutter can hang. We measure every run and give you a free, detailed, no-pressure estimate.
Should I choose 5-inch or 6-inch gutters?
Most homes use 5-inch K-style gutters, the residential standard, while 6-inch gutters are used for larger roofs. The right size depends on how much roof drains into each run and how many downspouts serve it. K-style sizing is an estimate, not a table lookup, so ask any contractor to explain the reasoning behind the size on your estimate.
Are 3x4 downspouts better than 2x3 downspouts?
For a main roof run, yes. A 2x3 downspout has a 6-square-inch cross section and a 3x4 has 12. Published gutter sizing guidance says downspouts under 7 square inches should not be used except for small areas such as porches and canopies. U.S. Department of Energy Building America guidance also says downspouts should end at least 5 feet from the foundation.
Will new gutters stop ice dams?
No, new gutters alone will not stop ice dams. University of Minnesota Extension traces ice dams to heat escaping the house and warming the roof unevenly, and it puts sealing ceiling air leaks first and adding insulation second. Clear soffit intake helps the attic ventilate, but we do not air seal ceilings or blow attic insulation, and we will say so before selling you gutters.
Does vented soffit installed over old solid soffit ventilate the attic?
No, not unless openings are cut in the old soffit first. The Polymeric Exterior Products Association installation manual says that when vented panels cover an existing soffit with no ventilation openings, an adequate number of openings must be cut. Attic insulation can also block the vents from inside, which is why U.S. Department of Energy Building America guidance calls for baffles at the eave.
Who handles the permits for gutter, fascia and soffit work?
We handle the permits. You get a free, detailed estimate first: we measure each gutter run, look over the fascia and soffit, and check the eave from inside the attic where we can reach it. The written scope then lists the gutter and downspout sizes, the fascia and soffit material and which eaves get vented panels.
More answers on our FAQ page.
Get Your Free Estimate
No pressure. No obligation. Just a straight answer on what your project will take and what it'll cost.
Central & Southeastern Pennsylvania